
As the best way to present ultra-thin TVs, there is no doubt that TVs are hung on the walls. This will not only improve the viewing angle, but also make the appearance of the TV more refined and blend in with the decoration of the entire room. However, TV wall hangings also have a lot of attention. Otherwise, if there are problems, the suspension will be unstable, and the television will be injured. Even if it comes to children, it is not good.
First of all, in order to ensure stability, the wall of the TV suspension must be a load-bearing wall. The so-called bearing wall refers to the wall that plays a supporting role in the house. In general, the framework around the building is a load-bearing wall, and the internal wall is generally not a load-bearing wall; while the self-built brick houses are all load-bearing walls. Of course, if you are not sure, the most secure way is to find a developer or property to request a drawing of your house.

Second, we must choose a rack. Different TVs must be equipped with suitable racks for normal use. There is no problem in using the racks provided by the manufacturers, but the prices are usually not very friendly. If you want to buy a third-party rack, be sure to ask the rack in advance. Does the salesperson support television at home to avoid spending money. The TV and the rack are connected through a set of screws at the rear of the TV. The hole spacing is generally divided into many sizes, such as 100×100, 200×200, 400×400, etc. Generally speaking, as long as the rack supports the hole pitch of the TV response, both are It can be installed normally.

Of course, it is also important to determine the position of the pylon. The height of the pylon should be the same as the head-up height of the audience sitting on the sofa. After the television is installed, the viewer's line of sight is right at the center of the TV screen. Many pylons now have tilt, tilt, and tilt adjustments to achieve more flexible viewing angles.

Finally, in order to ensure the stability of the pylon and the safety when watching television, it is best to install the pylon and ask a professional to install it and use different fixing bolts for different walls. After the hanger is mounted, shake it with your hands, and the bracket itself will not shake. Otherwise, you need to re-fix or tighten the fixing nut on the bracket.
Antenk manufactures a wide range of application specific board stacking connectors which were designed and built to specific customer requirements. Our experienced staff has developed custom products in a variety of contact styles, pitches and stacking heights. Our designs range from new concepts to duplicating existing market products identically or with improvements. Many desigsn are produced using automated manufacturing processes to increase reliability and provide significant cost savings
Board to Board Connector
Board-to-board (BTB) connectors as the name indicates is used for connecting circuits board together. This kind of connectors are suitable for stacking circuits boards one over another. Flat flexible cables can be avoided using these kinds of connectors; moreover it makes the entire unit more compact. The commonly used BTB connectors are SMT connectors and Berg Strip. We will discuss about them in detail in the following section.
SMT CONNECTOR
Surface Mount Technology (SMT) connector is a commonly found board-to-board connector in advanced circuit boards. As the name indicates this connector is available only in surface mount model. It is carefully mounted on to the solder pads on the surface of the PCB.
SMT connectors are ideal candidate for miniaturization due to their small area of occupancy and stacking height. They are suitable for double layered or multilayered PCBs. They are designed for high performance and reliability.
They commonly found in advanced circuit boards in networking equipment, telephones, mobile phones, computers and other consumer electronics.
Board-to-board (BTB) connectors are used to connect printed circuit boards (PCB), electronic components that contain a conductive pattern printed on the surface of the insulating base in an accurate and repeatable manner. Each terminal on a BTB connector is connected to a PCB. A BTB connector includes housing and a specific number of terminals. The terminal is made from a conductive material (mostly copper alloy), and plated to improve conductivity and antirust. Terminals transmit the current/signal between PCBs connected by BTB; the housing is made of insulating material (mostly plastic).
The basic types of Board to Board Connector
Broadly speaking, board to board connectors are manufactured in the following types:
Pin Header
Elevated Pin Header
Socket
Elevated Socket
Shrouded Header
Box Header
The way mount Board to Board Connectors on a PCB
board to board connectors are available in through hole (TH) and Surface Mount (SMT) variants.
Locating pegs (also referred to as locating posts, alignment pins or board locks) are used to assist alignment of connectors to the PCB. Locating pegs are particularly useful when using surface mount components.
board to board connectors are available in the following pitches: 04mm/0.5mm/0.8mm/1.0mm/1.27mm/2.54mm/3.96mm/4.0mm
For experienced hardware designers choosing board to board connectors is second nature, for the uninitiated it can be daunting. We offer design support and will help guide you through the options available. If you need help with your board to board connector design, contact antenk. Where required antenk also offer non standard pitches.
0.4mm Board To Board Connectors,0.5mm Female Board To Board Connector,0.8mm 1.0 mmPcb Board To Board Connector,Board To Board Terminal Connectors
ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com